few years ago ....clone carbs - Printable Version +- Vintage Karting Forum (https://www.vintagekartforum.com) +-- Forum: Main forums (https://www.vintagekartforum.com/forumdisplay.php?fid=1) +--- Forum: General (https://www.vintagekartforum.com/forumdisplay.php?fid=2) +--- Thread: few years ago ....clone carbs (/showthread.php?tid=3108) Pages:
1
2
|
few years ago ....clone carbs - steve miller - 06-05-2021 few years ago I started a post about clone carbs .. steve wehlt scott kneisel myself Ronnie G.. rip we all added info .. there was detailed diagrams drill size charts ect... where is it ...??? few folks on facebook keep looking cuz I keep telling them its on here ...??? is it still on here .. simple yes or no ... RE: few years ago ....clone carbs - Jim Reiter - 06-05-2021 type in " Clone alky carbs " in the search barand it comes up! RE: few years ago ....clone carbs - steve miller - 06-05-2021 nope ..not it ...this was for gas ...scott kneisle had diagrams drill sizes we had throttle arm options mods there WAS... 100s post .. RE: few years ago ....clone carbs - Scott Kneisel - 06-06-2021 I will look and see what I can find RE: few years ago ....clone carbs - steve miller - 06-07-2021 scott,.,.yourself and whelte had beautiful detailed info ...pics diagrams drill sizes ...etc... hope someone saved it ..... RE: few years ago ....clone carbs - Mark Loraine - 06-08-2021 Can anyone confirm that this kit on eBay are drill blanks that can be used for checking Carburetor Orifices and passageways. https://www.ebay.com/itm/293193678141 I assume these would be more accurate than sharp drill bits when checking the carburetor out for OEM specs? Thanks, mark RE: few years ago ....clone carbs - David Luciani - 06-08-2021 steve, i'll look for it. i am on road to recovery from this stupid sciatica that laid me out four weeks ago. am able to sit upright again and haven't all that much to do right now as i am supposed to be taking it easy. those posts may have been in old forum thus almost impossible to repost. may take a while to find them. i'm pretty sure i'll have time . i able to get around now at least but can't work just yet. d RE: few years ago ....clone carbs - ted johnson - 06-08-2021 Mark, these are standard pin gauges. If the correct carb holes are between .011 and .060, these pin gauges should measure them O.K. I usually just find what drill number the carb should be and check the holes with the blunt end of my number drills. Having the gauge set is a plus. Big Dave, sorry you feel less than yourself! Hope things improve soon. Ted RE: few years ago ....clone carbs - Scott Kneisel - 06-09-2021 I just ordered some on eBay so I can check the orifices. I also use the blunt end of a new number drill set I only use to check carbs. From memory which isn't the greatest anymore I do remember drilling out the high speed needle orifice to 0.060" and the carb worked fine. I think that is the only modification I made other than setting the fulcrum to 0.075" down from the diaphragm surface and POP to around 12psi like I do with all my gas tillys. (06-08-2021, 01:04 PM)David Luciani Wrote: steve, Sorry Dave, I struggled with that for almost a year, it is the worst. Mine turned out to be a cyst on a nerve root that finally drained. I had 4 cortisone shots in my spine that did absolutely nothing. The surgeon even tried to drain the cyst with a guided needle that lifted me off the table about a foot...Pain like I never felt. That didn't help either. Another surgeon told me to hang on and the cyst would drain by itself eventually and he was correct. I also did acupuncture which did give me some relief, never believed in it until then. Hang on, it should get better. Too bad you are laid up, I was kind of hoping you might make it to our Avon Antique reunion. "Life happens when you have other plans" (John Lennon) Avon 2011 017.jpg (Size: 1.22 MB / Downloads: 11) RE: few years ago ....clone carbs - steve miller - 06-09-2021 hi scott .. did you drill the dump tube along with needle orifice do you think pop off at 9 is to low . jeez all my junk runs ok ...to me anyways .lol. dave hope get some relief soon .. 4 or 5 years ago I got knocked off a road sign I was fixin ..15 feet or so landed on my feet crush 4 disc in my back..punctured a lung ..wheel chair for 4 months ..I feel for ya ... |